How To Replace Pur Water Filter Faucet

Download Article

PUR has multiple products available for filtering water, simply the filters get less effective over fourth dimension as they fill with contaminants. How you lot replace the filter depends on which system you're using. If you have a plastic pitcher or dispenser yous keep in the fridge, soak the new filter before screwing it in. For filtration systems that attach to your sink faucet, just remove the old filter and then yous can put the new 1 in its place. When you're finished, you'll have clean water to drink for another few months!

ane
Soak the replacement filter in common cold h2o for fifteen minutes. Place the new filter in a clean container that's deep enough so you can fully submerge it. Fill the container with cold water and go out it alone for at least 15 minutes. During this time, any backlog carbon from the filter volition elevator out and separate so it doesn't arrive your drinking water.^[1]
- Soaking the filter likewise ensures that water flows evenly when you use it.
- Don't use water warmer than 86 °F (30 °C) since it could damage the filter.
Warning: Avoid using 3rd-party filters with your PUR pitcher or dispenser since they may not fit besides or have been tested as efficiently.
two
Twist the old filter counterclockwise to remove it. Have the lid off of the pitcher or dispenser and set it aside. Then, lift upward the cascade tray, which is the blue plastic reservoir on top, and take it out. Take hold of the cylindrical filter from the bottom and rotate information technology counterclockwise so it unhooks from the filter. Pull the old filter out through the top of the pour tray and throw in the garbage.^[2]
- Look until the cascade tray is empty to change your filter, or else it may be hard to remove or you may spill.
Advertisement
3
Rinse the new filter nether your faucet for x seconds. Take the filter out of the container when it'south finished soaking and hold it underneath your faucet. Turn on common cold water and rotate the filter and so yous can rinse it off completely. Subsequently 10 seconds, turn off the water and milkshake out whatever backlog that's still in the filter.^[iii]
- Don't use hot water to rinse the filter off, or else yous may damage it.
four
Screw the filter clockwise into the cascade tray to secure it. Slide the long, cylindrical function of the filter through the pigsty in the eye of the pour tray and push it downwards equally far as it goes. Agree the filter by the bottom and rotate it clockwise until y'all hear information technology click into identify. Try borer on the end of the filter to make sure it doesn't pop out from the cascade tray. Identify the pour tray back into the pitcher or dispenser before replacing the lid.^[four]
- If the filter does pop out of the cascade tray, then you lot didn't properly secure information technology. Reinsert it and attempt turning information technology clockwise over again.
- PUR filters for pitchers and dispensers usually piece of work for 40 gallons (150 L), or approximately ii months.
5
Hold the Reset button down for 5 seconds if your bullpen or dispenser has i. Some newer PUR pitchers and dispensers have sensors that notice when you need to supplant the filter. Correct later on yous replace the filter, press the Reset button on the lid and proceed it held down for 5 seconds. A green light will blink on the lid in one case the sensor resets.^[v]
- Older pitchers or dispensers may not have an electronic brandish.
Advertisement

ane
Unscrew the filtration system from your faucet. Support the weight of the filtration arrangement with your nondominant hand and then it doesn't fall and pause. Rotate the plastic locking nut property the filtration system to the faucet counterclockwise to loosen it. Once you unscrew the system completely, carefully lift it away from the faucet and set information technology down on a countertop or towel.^[6]
- Water may spill out from the faucet when you lot unscrew the filtration system.
- Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling it direct downward from the faucet.
two
Twist open up the elevation comprehend of the system to remove the erstwhile filter. Hold the filtration system so the rounded end of the large cylinder points upward. Unscrew the summit from the cylinder by rotating it counterclockwise, and set the comprehend aside. Pull the old filter straight out from the system and throw it away in your trash.^[7]
- The top cover is always on the opposite stop of the spout that dispenses water.
iii

Ready the new filter inside of the system and screw on the cover. Make sure the narrower end of the filter is on the lesser and the logo is correct-side up. Place the filter into the filtration arrangement so information technology has a loose fit. Set the top cover dorsum over the filter and screw it into place to secure it.^[eight]
4
Reattach the filtration arrangement to your faucet. Hold the filtration organization against the lesser of the faucet and then the threadings are perfectly horizontal, or else they won't form a tight seal. Rotate the locking nut clockwise onto the faucet and continue tightening it until information technology's hand-tight. Turn on the water and make sure information technology doesn't drip or leak at the seam.^[9]
- If your filtration organisation doesn't screw on, line it up with the faucet and apply firm pressure to snap it on.
five
Run cold water through the filtration system for five minutes. Turn the handle on the right side of the filtration system to divert the h2o through the filter. Allow the h2o to run through the filter for 5 minutes to get rid of any remainder inside and then it works more efficiently. Afterwards that, you can utilise the filter immediately after turning it on.^[10]
- PUR faucet filters work for 100 gallons (380 L) of h2o, or near 3 months of utilise.
- Don't run water over 100 °F (38 °C) through the filter since y'all could harm information technology.
Alert: The h2o may sputter or await cloudy when you lot first utilise the new filter, only it will get better as you run water through it.

Advertisement

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Many PUR filtration systems have electronic lights that discover when you demand to change your filter. If y'all see a green light wink, you don't need to change your filter. If information technology blinks yellowish or scarlet, so you need to replace the filter before long.^[11]

Thanks for submitting a tip for review!

Don't use h2o that'south to a higher place 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since it can harm the filter.^[12]
Merely apply the filter with water that's already safe to drinkable since information technology volition not remove bacteria or infection.^[13]